Olika mekaniska egenskaper hos PP-rör

2021-11-09

Ningbo Fangli Technology Co., Ltd. är en tillverkare av mekanisk utrustning med nästan 30 års erfarenhet av plast rörextruderingsutrustning, nytt miljöskydd och nya material Utrustning. Sedan starten har Fangli utvecklats utifrån användarnas krav. Genom ständiga förbättringar, oberoende FoU i kärnan teknologi och matsmältning & absorption av avancerad teknik och annat innebär att vi har utvecklat PVC-rörsträngsprutningslinje, PP-R rörsträngsprutningslinje, PE vattenförsörjning / gasledning extrudering linje, som rekommenderades av kineserna Ministeriet för byggande för att ersätta importerade produkter. Vi har vunnit titeln av "Förstklassigt varumärke i Zhejiang-provinsen".

 

In the previous period, PP-C pipes and fittings appeared on the market, and the installation method was consistent with PP-R. Many people are confused about the difference between PP-R and PP-C, causing many misunderstandings and confusion. In international standards, polypropylene hot and cold water pipes are classified into PP-H, PP-B and PP-R, and there is no PP-C. The difference between the three types of PP pipes is that the stiffness of the PP-H, PP-B and PP-R pipes is successively decreased, and the impact strength is sequentially increased.

 

Bland de tre typerna av PP-rör, röret slagtålighet PP-R>PP-B>PP-H, rörvärmeförvrängningstemperatur PP-H>PP-B>PP-R, rörstyvhet PP-H>PP-B>PP-R, rörtemperatur blästringstemperatur PP-H>PP-B och PP-R, rör kemikaliebeständighet PP-H>PP-B och PP-R. Jämfört med andra PP-rör har PP-R-röret enastående fördelar med att förbättra lågtemperatursprödheten hos PP-H och god långvarig vattentrycksbeständighet vid högre temperaturer (60 °C), speciellt för varmvattenledningar. Vid användning är den långsiktiga styrkan bättre än PP-H och PP-B.

 

The PP-C pipe on the market is actually a PP-B pipe, and the raw material is a block copolymer polypropylene pipe special material. PP-B pipe is a kind of hot and cold water pipe, the price is relatively cheap, and its heat resistance and pressure resistance are very different from those of PP-R. For example: using conditional classification 2, design pressure 0.6MPa DN25mm pipe, PP-R pipe wall thickness 3.5mm, PP-B (PP-C) pipe wall thickness 5.1mm; design pressure 0.8MPa DN25mm, PP-R pipe wall thickness 4.2mm, but PP-B (PP-C) can not be used. Because the required wall thickness is too thick. The PP-C pipe with the same structural size and PP-R on the market has much lower operating conditions and cannot be mixed with the PP-R pipe. It is also impossible to replace the PP-R pipe with a PP-C pipe after determining the conditions of use. The use condition 2 indicates a design temperature of 70 ° C for hot water supply.

 

Om du behöver mer information, Ningbo Fangli Technology Co., Ltd. välkomnar dig att kontakta för en detaljerad förfrågan, vi kommer ge dig professionell teknisk vägledning eller utrustningsanskaffning förslag.


https://www.fangliextru.com/solid-wall-pipe-extrusion-equipment

https://www.fangliextru.com/special-use-pipe-extrusion-system

  • Email
  • QR
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy